Menu

Wednesday, 1 December 2010

Transient Analysis of a Cantilever Beam

Posted By On 09:35



Introduction

This tutorial was created using ANSYS 7.0 The purpose of this tutorial is to show the steps involved to perform a simple transient analysis.
Transient dynamic analysis is a technique used to determine the dynamic response of a structure under a time-varying load.
The time frame for this type of analysis is such that inertia or damping effects of the structure are considered to be important. Cases where such effects play a major role are under step or impulse loading conditions, for example, where there is a sharp load change in a fraction of time.
If inertia effects are negligible for the loading conditions being considered, a static analysis may be used instead.
For our case, we will impact the end of the beam with an impulse force and view the response at the location of impact.
Since an ideal impulse force excites all modes of a structure, the response of the beam should contain all mode frequencies. However, we cannot produce an ideal impulse force numerically. We have to apply a load over a discrete amount of time dt.
After the application of the load, we track the response of the beam at discrete time points for as long as we like (depending on what it is that we are looking for in the response).
The size of the time step is governed by the maximum mode frequency of the structure we wish to capture. The smaller the time step, the higher the mode frequency we will capture. The rule of thumb in ANSYS is
time_step = 1 / 20f
where f is the highest mode frequency we wish to capture. In other words, we must resolve our step size such that we will have 20 discrete points per period of the highest mode frequency.
It should be noted that a transient analysis is more involved than a static or harmonic analysis. It requires a good understanding of the dynamic behavior of a structure. Therefore, a modal analysis of the structure should be initially performed to provide information about the structure's dynamic behavior.
In ANSYS, transient dynamic analysis can be carried out using 3 methods.

  • The Full Method: This is the easiest method to use. All types of non-linearities are allowed. It is however very CPU intensive to go this route as full system matrices are used.
  • The Reduced Method: This method reduces the system matrices to only consider the Master Degrees of Freedom (MDOFs). Because of the reduced size of the matrices, the calculations are much quicker. However, this method handles only linear problems (such as our cantilever case).
  • The Mode Superposition Method: This method requires a preliminary modal analysis, as factored mode shapes are summed to calculate the structure's response. It is the quickest of the three methods, but it requires a good deal of understanding of the problem at hand.
We will use the Reduced Method for conducting our transient analysis. Usually one need not go further than Reviewing the Reduced Results. However, if stresses and forces are of interest than, we would have to Expand the Reduced Solution.

Preprocessing: Defining the Problem

The simple cantilever beam is used in all of the Dynamic Analysis Tutorials. If you haven't created the model in ANSYS, please use the links below. Both the command line codes and the GUI commands are shown in the respective links.

Solution: Assigning Loads and Solving


  1. Define Analysis Type

    • Select Solution > Analysis Type > New Analysis > Transient
    • The following window will appear. Select 'Reduced' as shown.

  2. Define Master DOFs

    • Select Solution > Master DOFs > User Selected > Define
    • Select all nodes except the left most node (at x=0).The following window will open, choose UY as the first dof in this window

      For an explanation on Master DOFs, see the section on Using the Reduced Method for modal analysis.

  3. Constrain the BeamSolution Menu > Define Loads > Apply > Structural > Displacement > On nodes
    Fix the left most node (constrain all DOFs).
  4. Apply Loads
    5. We will define our impulse load using Load Steps. The following time history curve shows our load steps and time steps. Note that for the reduced method, a constant time step is required throughout the time range.
    We can define each load step (load and time at the end of load segment) and save them in a file for future solution purposes. This is highly recommended especially when we have many load steps and we wish to re-run our solution.
    We can also solve for each load step after we define it. We will go ahead and save each load step in a file for later use, at the same time solve for each load step after we are done defining it.

    1. Load Step 1 - Initial Conditions

      1. Define Load StepWe need to establish initial conditions (the condition at Time = 0). Since the equations for a transient dynamic analysis are of second order, two sets of initial conditions are required; initial displacement and initial velocity. However, both default to zero. Therefore, for this example we can skip this step.
      2. Specify Time and Time Step Options

        • Select Solution > Load Step Opts > Time/Frequenc > Time - Time Step ..
          • set a time of 0 for the end of the load step (as shown below).
          • set [DELTIM] to 0.001. This will specify a time step size of 0.001 seconds to be used for this load step.
      3. Write Load Step File

        • Select Solution > Load Step Opts > Write LS FileThe following window will appear

        • Enter LSNUM = 1 as shown above and click 'OK'The load step will be saved in a file jobname.s01
    2. Load Step 2

      1. Define Load Step

        • Select Solution > Define Loads > Apply > Structural > Force/Moment > On Nodes and select the right most node (at x=1). Enter a force in the FY direction of value -100 N.
      2. Specify Time and Time Step Options

        • Select Solution > Load Step Opts > Time/Frequenc > Time - Time Step .. and set a time of 0.001 for the end of the load step
      3. Write Load Step FileSolution > Load Step Opts > Write LS FileEnter LSNUM = 2
    3. Load Step 3

      1. Define Load Step

        • Select Solution > Define Loads > Delete > Structural > Force/Moment > On Nodes and delete the load at x=1.
      2. Specify Time and Time Step Options

        • Select Solution > Load Step Opts > Time/Frequenc > Time - Time Step .. and set a time of 1 for the end of the load step
      3. Write Load Step FileSolution > Load Step Opts > Write LS FileEnter LSNUM = 3

  5. Solve the System

    • Select Solution > Solve > From LS FilesThe following window will appear.

    • Complete the window as shown above to solve using LS files 1 to 3.

Postprocessing: Viewing the Results

To view the response of node 2 (UY) with time we must use the TimeHist PostProcessor (POST26).

  1. Define VariablesIn here we have to define variables that we want to see plotted. By default, Variable 1 is assigned eitherTime or Frequency. In our case it is assigned Frequency. We want to see the displacement UY at the node at x=1, which is node #2. (To get a list of nodes and their attributes, select Utility Menu > List > nodes).

    • Select TimeHist Postpro > Variable Viewer... and the following window should pop up.
    • Select Add (the green '+' sign in the upper left corner) from this window and the following window should appear
    • We are interested in the Nodal Solution > DOF Solution > Y-Component of displacement. Click OK.
    • Graphically select node 2 when prompted and click OK. The 'Time History Variables' window should now look as follows
  2. List Stored Variables

    • In the 'Time History Variables' window click the 'List' button, 3 buttons to the left of 'Add'The following window will appear listing the data:
  3. Plot UY vs. frequency

    • In the 'Time History Variables' window click the 'Plot' button, 2 buttons to the left of 'Add'The following graph should be plotted in the main ANSYS window.

      A few things to note in the response curve

      • There are approximately 8 cycles in one second. This is the first mode of the cantilever beam and we have been able to capture it.
      • We also see another response at a higher frequency. We may have captured some response at the second mode at 52 Hz of the beam.
      • Note that the response does not decay as it should not. We did not specify damping for our system.

Expand the Solution

    For most problems, one need not go further than Reviewing the Reduced Results as the response of the structure is of utmost interest in transient dynamic analysis.
    However, if stresses and forces are of interest, we would have to expand the reduced solution.
    Let's say we are interested in the beam's behaviour at peak responses. We should then expand a few or all solutions around one peak (or dip). We will expand 10 solutions within the range of 0.08 and 0.11 seconds.

  1. Expand the solution

    • Select Finish in the ANSYS Main Menu
    • Select Solution > Analysis Type > ExpansionPass... and switch it to ON in the window that pops open.
    • Select Solution > Load Step Opts > ExpansionPass > Single Expand > Range of Solu's
    • Complete the window as shown below. This will expand 10 solutions withing the range of 0.08 and 0.11 seconds
  2. Solve the System
    3. Solution > Solve > Current LS
    SOLVE
  3. Review the results in POST1Review the results using either General Postprocessing (POST1) or TimeHist Postprocessing(POST26). For this case, we can view the deformed shape at each of the 10 solutions we expanded.

Damped Response of the Cantilever Beam

We did not specify damping in our transient analysis of the beam. We specify damping at the same time we specify our time & time steps for each load step.
We will now re-run our transient analysis, but now we will consider damping. Here is where the use of load step files comes in handy. We can easily change a few values in these files and re-run our whole solution from these load case files.

  • Open up the first load step file (Dynamic.s01) for editing Utility Menu > File > List > Other > Dynamic.s01. The file should look like the following..
    /COM,ANSYS RELEASE  5.7.1  UP20010418       14:44:02    08/20/2001
    /NOPR
    /TITLE, Dynamic Analysis                                                       
    _LSNUM=   1
    ANTYPE, 4
    TRNOPT,REDU,,DAMP
    BFUNIF,TEMP,_TINY
    DELTIM, 1.000000000E-03
    TIME,  0.00000000
    TREF,  0.00000000
    ALPHAD,  0.00000000
    BETAD,  0.00000000
    DMPRAT,  0.00000000
    TINTP,R5.0, 5.000000000E-03,,,
    TINTP,R5.0, -1.00000000    , 0.500000000    , -1.00000000
    NCNV,     1,  0.00000000    ,     0,  0.00000000    ,  0.00000000
    ERESX,DEFA
    ACEL,  0.00000000    ,  0.00000000    ,  0.00000000
    OMEGA,  0.00000000    ,  0.00000000    ,  0.00000000    ,     0
    DOMEGA,  0.00000000    ,  0.00000000    ,  0.00000000
    CGLOC,  0.00000000    ,  0.00000000    ,  0.00000000
    CGOMEGA,  0.00000000    ,  0.00000000    ,  0.00000000
    DCGOMG,  0.00000000    ,  0.00000000    ,  0.00000000

    D,      1,UX  ,  0.00000000    ,  0.00000000    
    D,      1,UY  ,  0.00000000    ,  0.00000000    
    D,      1,ROTZ,  0.00000000    ,  0.00000000    
    /GOPR
  • Change the damping value BETAD from 0 to 0.01 in all three load step files.
  • We will have to re-run the job for the new load step files. Select Utility Menu > file > Clear and Start New.
  • Repeat the steps shown above up to the point where we select MDOFs. After selecting MDOFs, simply go to Solution > (-Solve-) From LS files ... and in the window that opens up select files from 1 to 3 in steps of 1.
  • After the results have been calculated, plot up the response at node 2 in POST26. The damped response should look like the following

ANSYS Command Listing

finish
/clear 
    
/TITLE, Dynamic Analysis
/FILNAME,Dynamic,0  ! This sets the jobname to 'Dynamic'   
/PREP7    ! Enter preprocessor
K,1,0,0    ! Keypoints
K,2,1,0 
L,1,2      ! Connect keypoints with line

ET,1,BEAM3     ! Element type
R,1,0.0001,8.33e-10,0.01 ! Real constants

MP,EX,1,2.068e11  ! Young's modulus
MP,PRXY,1,0.33    ! Poisson's ratio
MP,DENS,1,7830    ! Density

LESIZE,ALL,,,10   ! Element size
LMESH,1    ! Mesh the line

FINISH  
/SOLU      ! Enter solution phase

ANTYPE, TRANS   ! Transient analysis
  
TRNOPT,REDUC,          ! reduced solution method
DELTIM,0.001   ! Specifies the time step sizes

!At time equals 0s
NSEL,S,,,2,11,          ! select nodes 2 - 11
M,All,UY, , ,            ! Define Master DOFs
NSEL,ALL     ! Reselect all nodes
 
D,1,ALL           ! Constrain left end

F,2,FY,-100   ! Load right end
!*

!At time equals 0.001s
TIME,0.001   ! Sets time to 0.001 seconds
KBC,0    ! Ramped load step
FDELE,2,ALL     ! Delete the load at the end
!*

!At time equals 1s
TIME,1     ! Sets time to 1 second
KBC,0    ! Ramped load step
!*

LSSOLVE,1,3,1         ! solve multiple load steps
 
FINISH  
/POST26    ! Enter time history

FILE,'Dynamic','rdsp','.' ! Calls the dynamic file
 
NSOL,2,2,U,Y, UY_2  ! Calls data for UY deflection at node 2
STORE,MERGE     ! Stores the data
PLVAR,2,   ! Plots vs. time

!Please note, if you are using a later version of ANSYS,
!you will probably have to issue the LSWRITE command at the 
!end of each load step for the LSSOLVE command to function
!properly.  In this case, replace the !* found in the code 
!with LSWRITE and the problem should be solved.

0 comments:

Post a Comment

© MechDocs Blog | Designed By - Templatesyard | SEO Plugin By - ABT | Distributed By Gooyaabi Templates